Improve the Look of Your Bathroom on a Budget

Bathroom Designs Simple Bathroom Design Commercial Bathrooms Designs Improve the Look of Your Bathroom on a Budget

Bathroom Renovation - A Step by Step Guide

Bathrooms are among the smallest rooms in the house and they are generally also certainly the most costly to renovate. Bathroom renovation can be a job that, if done well, will add value to a home plus a great space brimming with design and light.
Improve the Look of Your Bathroom on a Budget

Bathroom design
Bathroom design will be the first part of a bath room renovation you need to get right. Just replacing the prevailing bathroom with the same design may not be enough. The key to great bathroom design is usually to design it with all the people that are going to utilize it planned. However make certain that your bathroom design boasts an overall use factor too.

For example: If you were designing your bathrooms for families you may still design the bathroom with quick access for the shower and bath. This would be sure that the structure would recieve treatment if you have limited mobility. This means if you sell your house or if you happen to be renovating for profit your design carries a wider market appeal. Great bathroom design also uses space well, looking at the light or window space, size of fittings, and drainage options. Draw out a plan to scale and all the way down the sizes of the room. Mark the prevailing drainage points then and water inlet points. Write down a wish listing of the lavatory fittings to wish and want with their sizes. Now marry the 2 together and discover what fits. Note: Most bathroom drainage and water inlet points can be moved but this does come at extra expense.
Commercial Bathroom Design  Interior design

Bathroom remodel
If you've decided to complete the job yourself or part of the work it can be time to work with a skip bin and grab the previous bathroom. If your home appeared pre 1980 you may have fibro bathroom wall linings with asbestos in it and great care will have to be taken. You will need some full body disposable overalls, eye protection, and quality dust mask. Check with the local building authority or council regarding the regulation on bathroom asbestos wall lining removal.
Remove everything except the plumbing. If you keep the toilet plumbing in position you do not have to turn the lake off for the entire house. Also you will need to jack hammer the floor tiles up and also the sand and cement bed that they're laid on.
15+ Commercial Bathroom Designs, Decorating Ideas  Design Trends  Premium PSD, Vector Downloads

Bathroom Renovation and construction
Bathrooms have to be construction properly from the start to ensure that the finished job is correct and true. This also ensures the design and appear of the restroom will have an excellent finish
The Bathroom Renovation Process

Install water and drainage pipe and electrical wires.

Install wall lining and ceiling after which install the bathtub hob and bath.

Waterproof the ground and shower and bath recess.

Correct december the floor with sand and cement ready for tiling.

Lay floor and wall tiles and then grout.

Install new bathroom vanity, fittings, and taps - install new electrical.
15+ Commercial Bathroom Designs, Decorating Ideas  Design Trends  Premium PSD, Vector Downloads


Paint ceiling and final  one - Plumbing and electrical
At this aspect many new plumbing is installed for clean hot and cold water and drainage. Careful attention should be taken when positioning the brand new plumbing so that the plumbing fittings are correct when the tiling is completed. For example: To centre a fitting in a shower recess you should consider the thickness of the wall board, tile glue and tile hence the fitting will likely be centred after the tiles are in position. The same applies to installing drainage pipes for the toilet; the wall lining and tile thickness should be taken into account hence the pipe is in the correct position once the toilet is installed after tiling. Also rough in the any new electrical wires without connecting them on the mains power.
Commercial Bathroom Design  Interior design

Step two - Install wall and ceiling linings
Install your 6mm wall lining fostering to nail the fibro board every 150mm without nailing into the brand new pipes and electrical wires. The best way would be to measure and mark the pipe and wire layout on to your new wall board having a pencil while you go. Screw up (or nail) the ceiling lining, plasterboard could be the most common. However if you are laying your tiles from floor to ceiling don't install the cornice because done after tiling. If you might be not tiling on the ceiling go ahead and install the cornice following your wallboard and ceiling lining happen to be installed. Also if your bath is not freestanding it's simple to from the frame and install the tub. Ensure the bath is installed correctly enabling the thickness of the tiles and  sure to evaluate all linings and pipes when you continue with a bath room renovation.

Commercial Bathroom Design Interior design
Improve the Look of Your Bathroom on a Budget

Step three - Waterproof a bath room
Waterproof your bathrooms floor, shower recess, and around the tub. When waterproofing the bottom make sure that the waterproofing comes 100mm up the walls. The shower recess will need to be waterproofed 100mm higher than the shower rose outlet. Also the bath needs to be waterproofed 100mm higher than the lip in the bath around and to the floor. At the doorway install a 25 x 25mm aluminum angle glued into place with quality silicone and waterproof in the lip. Your whole bathroom should now the tanked, and so the all water will only go lower a drain. Bathroom waterproofing tip: waterproofing is a straightforward job but quality and accuracy is most crucial.
Step four - Lay in the cement screed for a floor.

Before the floor tiles can laid the floor must be smooth and fairly flat using a slight fall to the drainage outlet. To do this you have to use sand and cement mix which is far better to include a waterproofing agent into this as well. With a level, set the ground level with the doorway. Use the top aluminum angle because the finished floor level and measure down the thickness in the tile plus 10mm for the glue. Mark around the toilet with a level after which screed within your sand and cement mix with a 1 to 3 degree fall for the top from the drain outlet. Take your time and get it right using the finished level as smooth as is possible. When the sand cement mix has set but just isn't dry (you can walk onto it but you it is still somewhat soft) rub it over using a house brick. This will remove all of the small highs and lows and check using a level while you go. Let the toilet floor fully dry and after that you should have a great surface to tile onto. Tip: the harder work you set into the ground screed the easier your tiling will be.
15+ Commercial Bathroom Designs, Decorating Ideas Design Trends Premium PSD, Vector Downloads
Commercial Bathroom Design  Interior design

Step five: Tile floor and walls
Lay your tiles on a floor first and then grout. Then lay your wall tiles making sure actually level when you lay. Once the toilet tiles are actually cut and laid, grout your tiles and then buff the tiles clean.
Step six: Install plumbing fitting and fixtures
Install all of your plumbing fittings and taps. Also fit your entire towel rails and soap holders. Fit a new bathroom vanity making certain it is level and sealed round the top with silicone as well as seal around the bathtub. Tip: make sure they have been in the right place prior to deciding to drill to your tiles.
15+ Commercial Bathroom Designs, Decorating Ideas Design Trends Premium PSD, Vector Downloads
15+ Commercial Bathroom Designs, Decorating Ideas  Design Trends  Premium PSD, Vector Downloads

Step seven: painting, and cleaning - enjoy
Paint your ceiling and do a final clean ensuring that it is all totally fitted correctly and that there are no leaks with your plumbing. - Enjoy your bathroom.

Comments