DTR_studio Architects Designs a Stunning SingleFamily Home for a Painter in Málaga

Single Family Home Designs ARCHITECTURAL DESIGN STUDIO DTR_studio Architects Designs a Stunning SingleFamily Home for a Painter in Málaga

Bathroom Renovation - A Step by Step Guide

Bathrooms are some of the smallest rooms in the home and they are also the most costly to renovate. Bathroom renovation is a job that, if done well, can add value to your home along with a great space brimming with design and light.
DTR_studio Architects Designs a Stunning SingleFamily Home for a Painter in Málaga

Bathroom design
Bathroom design may be the first part of your bathroom renovation you should get right. Just replacing the existing bathroom with the same design may not be enough. The key to great bathroom design is always to design it with the people that will certainly put it to use in your mind. However ensure that a bath room design also has a general use factor as well.

For example: If you were designing a bathroom for families you could still design the lavatory with quick access to the shower and bath. This would ensure that the structure would also work for those who have limited mobility. This means if you opt to sell your home or if you are renovating for profit your design carries a wider market appeal. Great bathroom design also uses space well, considering the light or window space, sized fittings, and drainage options. Draw out an idea to scale and right down the sizes of your respective room. Mark the existing drainage points then and water inlet points. Write down a wish list of the lavatory fittings to wish and want making use of their sizes. Now marry the two together and see what fits. Note: Most bathroom drainage and water inlet points can be moved but this may come at extra cost.
 ARCHITECTURAL DESIGN STUDIO

Bathroom remodel
If you've decided to perform the work yourself or part of the project it can be time to employ a skip bin and retrieve the old bathroom. If your own home appeared pre 1980 you may have fibro bathroom wall linings with asbestos inside it and great care will have to be taken. You will need some full body disposable overalls, eye protection, and quality dust mask. Check with the local building authority or council concerning the regulation on bathroom asbestos wall lining removal.
Remove everything except the plumbing. If you keep the toilet plumbing in place you will not need to turn water off for your house. Also you should jack hammer the floor tiles up and also the sand and cement bed actually laid on.
SingleFamily, Custom Home Design, MidCentury Modern  Kirkland, WA  Shoesmith Cox Architects

Bathroom Renovation and construction
Bathrooms has to be construction properly from your ground-up to be sure that the finished job is correct and true. This also ensures the look and search of the bathroom can have a fantastic finish
The Bathroom Renovation Process

Install water and drainage pipe and electrical wires.

Install wall lining and ceiling and then install the bathtub hob and bath.

Waterproof the ground and shower and bath recess.

Correct december the ground with sand and cement ready for tiling.

Lay floor and wall tiles and after that grout.

Install new bathroom vanity, fittings, and taps - install new electrical.
modern house Archives  Off Some Design


Paint ceiling and final  one - Plumbing and electrical
At this point brand new plumbing is installed for clean cold and hot water and drainage. Careful attention has to be taken when positioning the new plumbing so your plumbing fittings are correct when the tiling is fully gone. For example: To centre a fitting in the shower recess you have to consider the thickness from the wall board, tile glue and tile and so the fitting is going to be centred as soon as the tiles are in position. The same applies to installing drainage pipes for any toilet; the wall lining and tile thickness has to be looked at so the pipe is incorporated in the correct position in the event the toilet is installed after tiling. Also rough within the any new electrical wires without connecting them to the mains power.
The Courtowers  Domus

Step two - Install wall and ceiling linings
Install your 6mm wall lining the constant maintenance to nail the fibro board every 150mm without nailing into the brand new pipes and electrical wires. The best way is to measure and mark the pipe and wire layout on to your new wall board which has a pencil while you go. Screw up (or nail) the ceiling lining, plasterboard may be the most common. However if you are laying your tiles from floor to ceiling do not install the cornice because most effectively achieved after tiling. If you happen to be not tiling towards the ceiling go ahead and install the cornice following the wallboard and ceiling lining are already installed. Also if your bath is just not freestanding now you can make up the frame and install the bath. Ensure the bathtub is installed correctly making it possible for the thickness in the tiles and  sure to test all linings and pipes prior to deciding to continue with a bath room renovation.

ARCHITECTURAL DESIGN STUDIO
DTR_studio Architects Designs a Stunning SingleFamily Home for a Painter in Málaga

Step three - Waterproof your bathroom
Waterproof your bathroom floor, shower recess, and around the bathtub. When waterproofing the bottom be sure that the waterproofing comes 100mm the walls. The shower recess should be waterproofed 100mm across the shower rose outlet. Also the tub must be waterproofed 100mm across the lip in the bath around and to the floor. At the doorway use a 25 x 25mm aluminum angle glued into place with quality silicone and waterproof in the lip. Your whole bathroom should now the tanked, therefore the all water will still only decrease a drain. Bathroom waterproofing tip: waterproofing is a straightforward job but quality and accuracy is most crucial.
Step four - Lay inside cement screed for the floor.

Before the ground tiles can laid the ground must be smooth and fairly flat using a slight fall to the drainage outlet. To do this you should use sand and cement mix in fact it is far better to add a waterproofing agent into this also. With a level, set the bottom level on the doorway. Use the top aluminum angle because finished floor level and measure along the thickness of the tile plus 10mm for the glue. Mark about the lavatory with a level and after that screed inside your sand and cement mix with a 1 to 3 degree fall on the top of the drain outlet. Take your time and have it right with the finished level as smooth as is possible. When the sand cement mix has set but isn't dry (you are able to walk into it but you it's still a lttle bit soft) rub it over with a house brick. This will remove every one of the small highs and lows and check with a level when you go. Let the restroom floor fully dry after which you really should have an incredible surface to tile onto. Tip: greater work you set into the ground screed the more your tiling is going to be.
SingleFamily, Custom Home Design, MidCentury Modern Kirkland, WA Shoesmith Cox Architects
 ARCHITECTURAL DESIGN STUDIO

Step five: Tile floor and walls
Lay your tiles on the floor first and after that grout. Then lay your wall tiles making sure that they are level when you lay. Once the restroom tiles happen to be cut and laid, grout your tiles after which buff the tiles clean.
Step six: Install plumbing fitting and fixtures
Install your entire plumbing fittings and taps. Also fit your entire towel rails and soap holders. Fit your new bathroom vanity making certain it really is level and sealed throughout the top with silicone as well as seal around the bathtub. Tip: make sure they will be in the right place prior to deciding to drill in your tiles.
modern house Archives Off Some Design
SingleFamily, Custom Home Design, MidCentury Modern  Kirkland, WA  Shoesmith Cox Architects

Step seven: painting, and cleaning - enjoy
Paint your ceiling and do a final clean ensuring things are fitted correctly understanding that there won't be any leaks within your plumbing. - Enjoy your new bathroom.

Comments